Hi Leo McCormack here Ecopipe Irl, having over seven years experience designing underfloor heating and getting feedback from the installers I have learned a few features all installers require.

1. A Design Including
2. Full Line Drawings
3. Heat Loss Calculations
4. Lengths Of Pipe Per Circuit
5. Correct Flow Rates
6. Longer Lengths of Pipe To Help Elliminate The Need for Joining The Pipe Under The Floor
7. Option For Laying Both Single, Double Meander And Reversal Spiral Piping Patterns
8. Option For A Polyethene Sheet With A 50mm Grid to Achieve Correct Pipe Spacings When Laying The Reverse Spiral Piping Patterns.
9. Pex Pipe with a 2 mm Cavity Wall In Lengths Of 600, 300, 120 Meters
10. Multilayer Pipe In Rolls Of 500, 200, 100 Meters
11. Auto Air Vents
12. Electrical Drawings
13. Heatmiser Controls, 12 and 230 volt options
14. Centeral Control
15. Telephone Link
16. Weather Compensation
17. Technical Support Both Over The Phone And Onsite

For All Your Underfloor Heating Design’s, Quotations Including Technical Support …Call Leo On Ph: 087 7785709

Sunstar Solar Solutions

Innovative Solar Solutions At “Discounted Factory Prices”…

Sunstar solar is a new company providing solar solutions at discounted factory prices. The objective is to bring quality solar solutions to the marketplace which have low environmental impact and are cost-effective to purchase and install.

Download the following Solar Pdf’s:

Please place your comments below:

YOUR RESULTS OF MARKET RESEARCH ON SOLAR CYLINDER:

Press Play To Hear A Personal Message From Ecopipe Ireland

ECOPIPE (IRL) SURVEYED A NUMBER OF RENEWABLE ENERGY INSTALLERS ACROSS THE COUNTRY TO FIND OUT WHAT FEATURES THEY REQUIRED IN A SOLAR CYLINDER KNOWING THAT WE WERE WORKING WITH A BLANK SHEET.

ECOPIPE ALSO INTERVIEWED TWO SOLAR PANEL MANUFACTURERS AND FINALLY CONCLUDED WITH AN ENVIRONMENTAL IMPACT REVIEW. THESE WERE THE RESULTS.

PLUMBERS TOP 10 REQUESTS:

 - USE A MANUFACTURER WITH A PROVEN RECORD IN THE IRISH MARKET IN STAINLESS STEEL CYLINDERS

 - KEEP THE CYLINDER TO A MAXIMUM HEIGHT OF 1.8M

 - MAKE SURE THE CYLINDER ACTUALLY HOLDS 300L OF WATER

 - MAKE SURE THE TRIPLE COIL HAS TWO 1” GRAVITY COILS

 - MAKE ALL THE PLUMBING CONNECTIONS IN A VERTICAL LINE ON ONE SIDE OF THE CYLINDER

 - PUT IN AN ACCESSABLE CLEANING DOOR FOR CLEANING PURPOSES

 - MAKE SURE AUXILLARY COIL WILL GIVE A MIN. OF 200L

 - PUT IN TWO IMMERSION TAPPINGS, TO ENSURE SUFFICIENT BACKUP

 - MAKE THE WATER CONNECTIONS BSP THREAD NOT COMPRESSION

 - MAKE THE UNVENTED KIT AN OPTIONAL EXTRA.

 SOLAR MANUFACTURERS RECOMMENDATIONS:

 - SOLAR COIL MINIMUM SIZE 1.2M2 TO ACCOMMODATE 6M2 SOLAR PANELS

 - POSITION SOLAR COIL AS LOW AS POSSIBLE IN THE CYLINDER TO MAXIMIZE THE SOLAR GAIN

 - POSITION CYLINDER SENSOR POCKET APPROX. 75mm FROM BOTTOM OF SOLAR COIL TO MAXIMISE SOLAR GAIN

 - MAKE ALLOWANCE FOR CLEANING THE CYLINDER AS LIMESCALE CAN BUILD UP AT THE BOTTOM OF CYLINDER

 ENVIRONMENTAL IMPACT REVIEW:

 - MAKE THE CYLINDER 100% RECYCLEABLE

 - INSULATION SHOULD BE EPS AS IT IS 100% RECYCLEABLE

 - INSULATE THE COMPLETE CYLINDER AND ESPECIALLY HAVE NO CONNECTIONS ON THE TOP  THAT IS WHERE THE GREATEST LOSSES OCCUR

 - MINIMISE STANDING LOSSES AND MAKE THEM AVAILABLE

 CONTACT US:

 North Contact; Kieran Ph: 086 8826576

 South Contact; Leo Ph: 087 7785709

 East Contact; Mac Ph: 087 2593085

 West Contact; Donagh Ph: 087 2899088

 Regards
Macartan McCague,
Managing Director,
Ecopipe IRL
Ph: 01 2960174
Mob: 087 2593085
Fax: 01 2960175
http://www.ecopipeirl.com/
http://www.ecopipeirl.com/solar.html

http://www.ecopipeirl.com/UnderFloor-Heating.html